Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.

THE NUMBER DIVERT ON OUR SYSTEM  IS NOW WORKING AGAIN.

Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

A standard Chronos wheel cutting engine (No 153) mounted on its original base and box cover. Comes with 2 count plates a DD62 and DD65 with center spindles and wheel holders and a second small cutter frame. The motor is 240 Volt single phase with a 3 speed pulley. This will [Read more…]

EMCO DIVIDING AND ROTARY TABLE

EMCO DIVIDING AND ROTARY TABLE

EMCO DIVIDING AND ROTARY TABLE

A very versatile piece of equipment allowing direct dividing up to 24 divisions or by using the 3 plates with the worm engaged a large number of divisions can be selected. It can also be used as a rotary table. The diameter of the table is 150mm and the central [Read more…]

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

A rare American HR triple crosslide that would suit WW pattern lathe beds. This is very similar to the Derbyshire and Webster Whitcomb makes. The chrome plating has aged a little and there is very slight flaking on one edge, there is a slight cut mark on the topslide (shown) but would not [Read more…]

HIGH PRECISION WATCH MAKERS DRILL

HIGH PRECISION WATCH MAKERS DRILL

HIGH PRECISION WATCH MAKERS DRILL

A very clean high precision drill with sensitive feel, no makers name on it but looks like Hauser or Dixi origin. The height of the drill is 14″ and has a single grooved pulley so would benefit from a variable speed motor, drive belting will be supplied. The table can [Read more…]

4 JAW CHUCK

4 JAW CHUCK

A very clean 59mm diameter 4 jaw independent chuck with a 12 x 1mm internal thread and register, would suit a late Cowells lathe. Comes with a key. Will Post UK only Royal Mail Special delivery for £10.00 including packing.

 

NOW SOLD

[Read more…]

WW PATTERN 8mm LATHE

WW PATTEN 8mm LATHE

WW PATTERN 8mm LATHE

A single foot ww pattern 8mm lathe, no makers mark but could be from Webster Whitcomb or another American company. Has been used but is in good condition with no cuts or marks on the bed and headstock bearings running smoothly. There a few chips on the composite headstock pulley but [Read more…]

2 BOXES OF SPARE STAKES

2 BOXES OF SPARE STAKES

2 BOXES OF SPARE STAKES

The two wooden containers hold 19 and 20 spare 4.7mm stakes that will fit most sets on the market today. They are marked Southern clock and watch supplies and the other “Precista”. All stakes are in good clean condition, one has been ground to fit the previous owners requirements it [Read more…]

PULTRA 10mm STEP CHUCKS

PULTRA 10mm STEP CHUCKS

A set of 5 10mm Pultra step chucks marked “Conflex ” so late models. These are in outstanding condition and probably not used, very light staining in some of the steps but otherwise as new. Will post UK only Royal Mail Special Delivery including packing for £8.60 or buyer collects or [Read more…]

LORCH SCHMIDT MANDREL HEADSTOCK

LORCH SCHMIDT MANDREL HEADSTOCK

LORCH SCHMIDT MANDREL HEADSTOCK

This “D” Bed headstock is in good used condition, there is no play in the bearings and the centring point is sharp. The nickel plating has come of the headstock in a few places so looks a little dull. The three plate clamps are all flat and have no damage. The [Read more…]

6mm Collets, Arbors, Box chucks.

6mm Collets, Arbors, Box chucks.

A selection of 6mm items including 29 X 6mm collets and 1 at 6.5mm. 2 box chucks, Grinding wheel arbors, cutter arbors, safe pulley and other items. These have all been used but are in good overall condition and would be ideal to fill up the spaces in a 6mm [Read more…]