Oops! It appears that you have disabled your Javascript. In order for you to see this page as it is meant to appear, we ask that you please re-enable your Javascript!

Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.

 

Tel: 01235 763987
Fax: 01235 769828

Browse our site

Reset

WATCHMAKERS DEPTHING TOOL

WATCHMAKERS DEPTHING TOOL

Good quality depthing tool in clean wooden case, points and centres in excellent condition, pins in line. Will post UK only Royal mail special delivery including packing for £10.00.

PRICE £35.00

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

A standard Chronos wheel cutting engine (No 153) mounted on its original base and box cover. Comes with 2 count plates a DD62 and DD65 with center spindles and wheel holders and a second small cutter frame. The motor is 240 Volt single phase with a 3 speed pulley. This will […]

FAVORITE 2 8mm HIGH PRECISION LATHE

FAVORITE 2 8mm HIGH PRECISION LATHE

FAVORITE 2 8mm HIGH PRECISION LATHE

A rare chance to own one of the best 8mm lathes built. This double foot version of the Favorite 2 mounted on a solid wooden base and powered by a Parvalux 240 volt mains motor is in fine condition. The lathe has been used and looked after for many […]

PUNCH AND STAKE SET

PUNCH AND STAKE SET

PUNCH AND STAKE SET

A mint condition 24 piece punch and stake set for fine work. The stake diameter is 2.99mm and they are in a unmarked wooden box. Will post UK only Royal Mail Special Delivery including packing for £8.50.

PRICE £ 28.00

[…]

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

A rare American HR triple crosslide that would suit WW pattern lathe beds. This is very similar to the Derbyshire and Webster Whitcomb makes. The chrome plating has aged a little and there is very slight flaking on one edge, there is a slight cut mark on the topslide (shown) but would not […]

4 JAW CHUCK

4 JAW CHUCK

A very clean 59mm diameter 4 jaw independent chuck with a 12 x 1mm internal thread and register, would suit a late Cowells lathe. Comes with a key. Will Post UK only Royal Mail Special delivery for £10.00 including packing.

PRICE £40.00

[…]

WW PATTERN 8mm LATHE

WW PATTEN 8mm LATHE

WW PATTERN 8mm LATHE

A single foot ww pattern 8mm lathe, no makers mark but could be from Webster Whitcomb or another American company. Has been used but is in good condition with no cuts or marks on the bed and headstock bearings running smoothly. There a few chips on the composite headstock pulley but […]

2 BOXES OF SPARE STAKES

2 BOXES OF SPARE STAKES

2 BOXES OF SPARE STAKES

The two wooden containers hold 19 and 20 spare 4.7mm stakes that will fit most sets on the market today. They are marked Southern clock and watch supplies and the other “Precista”. All stakes are in good clean condition, one has been ground to fit the previous owners requirements it […]

PULTRA 10mm STEP CHUCKS

PULTRA 10mm STEP CHUCKS

A set of 5 10mm Pultra step chucks marked “Conflex ” so late models. These are in outstanding condition and probably not used, very light staining in some of the steps but otherwise as new. Will post UK only Royal Mail Special Delivery including packing for £8.60 or buyer collects or […]

LORCH SCHMIDT MANDREL HEADSTOCK

LORCH SCHMIDT MANDREL HEADSTOCK

LORCH SCHMIDT MANDREL HEADSTOCK

This “D” Bed headstock is in good used condition, there is no play in the bearings and the centring point is sharp. The nickel plating has come of the headstock in a few places so looks a little dull. The three plate clamps are all flat and have no damage. The […]