Oops! It appears that you have disabled your Javascript. In order for you to see this page as it is meant to appear, we ask that you please re-enable your Javascript!

Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.

 

Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

GERMAN PIVOTER JACOT TOOL

GERMAN PIVOTER JACOT TOOL

This offset Jacot tool has had good careful use. All the pivot plates (including 2 spares ) and drums show no signs of damage or wear. The box bears all the marks of being taken out a draw and replaced many times. No makers marks on the tool but finished to […]

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW (reversible) CHUCK

This will fit the early Unimat and other variants in the Emco range. In used but very good condition and could be fitted to other small lathes.Will post Royal Mail Special Delivery UK only including packing for£9.50.

NOW SOLD

[…]

EMCO SMALL MACHINE VICE

EMCO SMALL MACHINE VICE

This small machine vice has overall dimensions of 85mm long X 45mm wide X 34mm height. The jaws open to 31mm by 17mm deep, the static jaw has horizontal and vertical V cuts so round objects can be held easily. The vice has some oil and grease staining but is otherwise […]

8mm MANDREL PLATE & CENTRE

8mm MANDREL PLATE & CENTRE

Although not marked this is very much in the Pultra style. we have resurfaced the plate, One of the dogs has a slight rub mark on the top edge but all the gripping surfaces are unmarked. The pull back centre point is sharp and the guide bush allows the pin […]

L & R DEMAGNETIZER

L & R DEMAGNETIZER

L & R DEMAGNETIZER

Does Exactly what it says on the box, American made by L&R Kearney New Jersey. Mains (240 volt) powered and in full working order with instructions on the underside of the box. Can be used for whole watches as well as small parts, very easy to use. Will post Royal Mail […]

WATCHMAKERS DEPTHING TOOL

WATCHMAKERS DEPTHING TOOL

Good quality depthing tool in clean wooden case, points and centres in excellent condition, pins in line. Will post UK only Royal mail special delivery including packing for £10.00.

NOW SOLD

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

A standard Chronos wheel cutting engine (No 153) mounted on its original base and box cover. Comes with 2 count plates a DD62 and DD65 with center spindles and wheel holders and a second small cutter frame. The motor is 240 Volt single phase with a 3 speed pulley. This will […]

HIGH PRECISION WATCH MAKERS DRILL

HIGH PRECISION WATCH MAKERS DRILL

HIGH PRECISION WATCH MAKERS DRILL

A very clean high precision drill with sensitive feel, no makers name on it but looks like Hauser or Dixi origin. The height of the drill is 14″ and has a single grooved pulley so would benefit from a variable speed motor, drive belting will be supplied. The table can […]

4 JAW CHUCK

4 JAW CHUCK

A very clean 59mm diameter 4 jaw independent chuck with a 12 x 1mm internal thread and register, would suit a late Cowells lathe. Comes with a key. Will Post UK only Royal Mail Special delivery for £10.00 including packing.

PRICE £40.00

[…]

WW PATTERN 8mm LATHE

WW PATTEN 8mm LATHE

WW PATTERN 8mm LATHE

A single foot ww pattern 8mm lathe, no makers mark but could be from Webster Whitcomb or another American company. Has been used but is in good condition with no cuts or marks on the bed and headstock bearings running smoothly. There a few chips on the composite headstock pulley but […]