Oops! It appears that you have disabled your Javascript. In order for you to see this page as it is meant to appear, we ask that you please re-enable your Javascript!

Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.

Tel: 01235 763987
Fax: 01235 769828

Browse our site

Reset

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

A standard Chronos wheel cutting engine (No 153) mounted on its original base and box cover. Comes with 2 count plates a DD62 and DD65 with center spindles and wheel holders and a second small cutter frame. The motor is 240 Volt single phase with a 3 speed pulley. This will […]

FAVORITE 2 8mm HIGH PRECISION LATHE

FAVORITE 2 8mm HIGH PRECISION LATHE

FAVORITE 2 8mm HIGH PRECISION LATHE

A rare chance to own one of the best 8mm lathes built. This double foot version of the Favorite 2 mounted on a solid wooden base and powered by a Parvalux 240 volt mains motor is in fine condition. The lathe has been used and looked after for many […]

EMCO DIVIDING AND ROTARY TABLE

EMCO DIVIDING AND ROTARY TABLE

EMCO DIVIDING AND ROTARY TABLE

A very versatile piece of equipment allowing direct dividing up to 24 divisions or by using the 3 plates with the worm engaged a large number of divisions can be selected. It can also be used as a rotary table. The diameter of the table is 150mm and the central […]

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

A rare American HR triple crosslide that would suit WW pattern lathe beds. This is very similar to the Derbyshire and Webster Whitcomb makes. The chrome plating has aged a little and there is very slight flaking on one edge, there is a slight cut mark on the topslide (shown) but would not […]

HIGH PRECISION WATCH MAKERS DRILL

HIGH PRECISION WATCH MAKERS DRILL

HIGH PRECISION WATCH MAKERS DRILL

A very clean high precision drill with sensitive feel, no makers name on it but looks like Hauser or Dixi origin. The height of the drill is 14″ and has a single grooved pulley so would benefit from a variable speed motor, drive belting will be supplied. The table can […]

4 JAW CHUCK

4 JAW CHUCK

A very clean 59mm diameter 4 jaw independent chuck with a 12 x 1mm internal thread and register, would suit a late Cowells lathe. Comes with a key. Will Post UK only Royal Mail Special delivery for £10.00 including packing.

PRICE £40.00

[…]

PULTRA 10mm STEP CHUCKS

PULTRA 10mm STEP CHUCKS

A set of 5 10mm Pultra step chucks marked “Conflex ” so late models. These are in outstanding condition and probably not used, very light staining in some of the steps but otherwise as new. Will post UK only Royal Mail Special Delivery including packing for £8.60 or buyer collects or […]

SET OF 8mm STEP CHUCKS

SET OF 8mm STEP CHUCKS

SET OF 8mm STEP CHUCKS

A made up set of 8mm ring chucks in good used condition with some staining in the ring sections. They are probably of Pultra origin judging by the marks on them. Will post UK only Royal Mail Special Delivery only for £10.00 including Packing.

PRICE £85.00

[…]

Burnerd 32N 3 JAW CHUCK

Burnerd 32N 3 JAW CHUCK

A clean used example of this rare chuck, unlike the standard version this has 2 sets of jaws and has a larger capacity, the the chuck body is 56mm to the edge, and 62mm to the knurled closing ring. Will fit to 8mm and 10mm watch lathes,( and many others). […]

SET OF 6mm STEP CHUCKS

SET OF 6mm STEP CHUCKS

SET OF 6mm STEP CHUCKS

A very clean set of step chucks, slight oil or preservative staining on the ring section but otherwise in mint condition. There is no makers mark but they are very much in the style of the Lorch step collet. The thread is 5 x .7mm for the draw bar. Will […]