Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.


Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

THIEL PRODURO DIE FILLER

THIEL PRODURO DIE FILLER

THIEL PRODURO DIE FILLER

This is one of the best die fillers around. Built to a very high standard it has variable stroke and speed with both being adjustable whilst running. The table can be set in two planes so compound angles can be produced. This machine is [Read more…]

PULTRA 1750 10MM BENCH LATHE

PULTRA 1750 10MM BENCH LATHE

A well equipped clean bench model which just needs mounting on a bench with the Mardrive unit to be used straight away. The Mardrive is single phase 240 volt with switch gear and clutch and brake pedal. Comes with the following equipment:-

Set of 24 metric collets from .4 – [Read more…]

SWISS JEWELLING TOOL

SWISS JEWELING TOOL

SWISS JEWELLING TOOL

This Jewelling tool is marked SWISS made but has no brand and the box does not carry any identification mark, It does however have the same layout as the Favorite and carries the same inventory of parts. In used condition with the press being of cast iron [Read more…]

LORCH SCHMIDT SCREW HEAD POLISHER

LORCH SCHMIDT SCREW HEAD POLISHER

LORCH SCHMIDT SCREW HEAD POLISHER

A carefully used clean example of this very useful tool. It one of the brass collets is missing but otherwise is as shown. Weight is 1.5 kilos so can send UK only by Royal Mail special Delivery including packing for £12.00. Otherwise can [Read more…]

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

A clean used example of this well know lathe that is always popular with Model Makers, Horologists etc. Has some oil staining on the bed but is otherwise in very good condition. Comes with the following inventory of equipment:-

3 jaw reversable chuck [Read more…]

BOYLE WHEEL AND PINION CUTTING ENGINE

BOYLE WHEEL AND PINION CUTTING ENGINE

BOYLE WHEEL AND PINION CUTTING ENGINE

The Boyle wheel cutting engine is a robust and larger version of the Chronos style engine. Built in Frome Somerset this is serial No 32. and is equipped with gallows and centers for pinion cutting. The footprint is 24″ X 12″ [Read more…]

GERMAN PIVOTER JACOT TOOL

GERMAN PIVOTER JACOT TOOL

This offset Jacot tool has had good careful use. All the pivot plates (including 2 spares ) and drums show no signs of damage or wear. The box bears all the marks of being taken out a draw and replaced many times. No makers marks on the tool but finished to [Read more…]

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW (reversible) CHUCK

This will fit the early Unimat and other variants in the Emco range. In used but very good condition and could be fitted to other small lathes.Will post Royal Mail Special Delivery UK only including packing for£9.50.

NOW SOLD

[Read more…]

EMCO SMALL MACHINE VICE

EMCO SMALL MACHINE VICE

This small machine vice has overall dimensions of 85mm long X 45mm wide X 34mm height. The jaws open to 31mm by 17mm deep, the static jaw has horizontal and vertical V cuts so round objects can be held easily. The vice has some oil and grease staining but is otherwise [Read more…]

8mm MANDREL PLATE & CENTRE

8mm MANDREL PLATE & CENTRE

Although not marked this is very much in the Pultra style. we have resurfaced the plate, One of the dogs has a slight rub mark on the top edge but all the gripping surfaces are unmarked. The pull back centre point is sharp and the guide bush allows the pin [Read more…]