Oops! It appears that you have disabled your Javascript. In order for you to see this page as it is meant to appear, we ask that you please re-enable your Javascript!

Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.

 

Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

GERMAN PIVOTER JACOT TOOL

GERMAN PIVOTER JACOT TOOL

This offset Jacot tool has had good careful use. All the pivot plates (including 2 spares ) and drums show no signs of damage or wear. The box bears all the marks of being taken out a draw and replaced many times. No makers marks on the tool but finished to […]

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW (reversible) CHUCK

This will fit the early Unimat and other variants in the Emco range. In used but very good condition and could be fitted to other small lathes.Will post Royal Mail Special Delivery UK only including packing for£9.50.

NOW SOLD

[…]

EMCO SMALL MACHINE VICE

EMCO SMALL MACHINE VICE

This small machine vice has overall dimensions of 85mm long X 45mm wide X 34mm height. The jaws open to 31mm by 17mm deep, the static jaw has horizontal and vertical V cuts so round objects can be held easily. The vice has some oil and grease staining but is otherwise […]

L & R DEMAGNETIZER

L & R DEMAGNETIZER

L & R DEMAGNETIZER

Does Exactly what it says on the box, American made by L&R Kearney New Jersey. Mains (240 volt) powered and in full working order with instructions on the underside of the box. Can be used for whole watches as well as small parts, very easy to use. Will post Royal Mail […]

BOLEY & LEINEN 8mm RING STEP CHUCKS

BOLEY & LEINEN RING STEP CHUCKS

BOLEY & LEINEN RING STEP CHUCKS

These 5 Boley and Leinen ring step chucks are marked 1,3, and 5, 2and 4 are not. All are marked Boley and Leinen and cover the sizes in the set. They are all in excellent condition. Please call for any further information, The block is not supplied. Will post […]

WATCHMAKERS DEPTHING TOOL

WATCHMAKERS DEPTHING TOOL

Good quality depthing tool in clean wooden case, points and centres in excellent condition, pins in line. Will post UK only Royal mail special delivery including packing for £10.00.

NOW SOLD

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

CHRONOS WHEEL CUTTING ENGINE

A standard Chronos wheel cutting engine (No 153) mounted on its original base and box cover. Comes with 2 count plates a DD62 and DD65 with center spindles and wheel holders and a second small cutter frame. The motor is 240 Volt single phase with a 3 speed pulley. This will […]

FAVORITE 2 8mm HIGH PRECISION LATHE

FAVORITE 2 8mm HIGH PRECISION LATHE

FAVORITE 2 8mm HIGH PRECISION LATHE

A rare chance to own one of the best 8mm lathes built. This double foot version of the Favorite 2 mounted on a solid wooden base and powered by a Parvalux 240 volt mains motor is in fine condition. The lathe has been used and looked after for many […]

EMCO DIVIDING AND ROTARY TABLE

EMCO DIVIDING AND ROTARY TABLE

EMCO DIVIDING AND ROTARY TABLE

A very versatile piece of equipment allowing direct dividing up to 24 divisions or by using the 3 plates with the worm engaged a large number of divisions can be selected. It can also be used as a rotary table. The diameter of the table is 150mm and the central […]

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

A rare American HR triple crosslide that would suit WW pattern lathe beds. This is very similar to the Derbyshire and Webster Whitcomb makes. The chrome plating has aged a little and there is very slight flaking on one edge, there is a slight cut mark on the topslide (shown) but would not […]