Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive a reply.

I HAVE BEEN ADVISED BY CARL BARNES THAT THE BRUNEL CLOCK AND WATCH FAIR ON SUNDAY THE 5th APRIL HAS BEEN CANCELLED DUE TO THE CURRENT VIRUS SITUATION.

 

Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

VERTICAL WHEEL AND MILLING ATTACHMENT

VERTICAL WHEEL AND MILLING ATTACHMENT

VERTICAL WHEEL AND MILLING ATTACHMENT

An unusual and versatile wheel cutting and very light milling attachment that would be most suited on WW pattern lathe beds. Fitted with a small arbour to take 4.5mm bore wheel cutters, this can be removed and others made to hold other cutters [Read more…]

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

A clean used example of this well know lathe that is always popular with Model Makers, Horologists etc. Has some oil staining on the bed but is otherwise in very good condition. Comes with the following inventory of equipment:-

3 jaw reversable chuck [Read more…]

ARRAND BALL BEARING SPINDLE

ARRAND BALL BEARING SPINDLE

ARRAND BALL BEARING SPINDLE

A little used example of this well known make that has been used in model engineering and horology for many years sadly no longer available to buy new. This one comes with three 1 Morse adaptors for holding the following (1) 3/16th round toolsteel (2) 1/4 round toolsteel (3) to hold [Read more…]

COWELLS 90ME LATHE

COWELLS 90ME LATHE

COWELLS 90ME LATHE

A very well equipped example of this well known and widley used British made lathe. It is the older version with a 14X 1.25 mm nose thread,however the dividing head nose thread is 14X1.00mm. This one comes with the wheel and pinion cutting attachment and was set up to be used this [Read more…]

COWELLS 90E LATHE

COWELLS 90E LATHE

COWELLS 90E LATHE

This model is in mint condition with the added bonus of an inverter drive variable speed motor ( 240 volt mains input ) It has also been upgraded with the later spindle with 14 x 1 mm nose thread and metric slip dials. A brand new Sherline reversable 3 jaw chuck and [Read more…]

SCHAUBLIN 102 PLAIN LATHE

SCHAUBLIN 102- 80 PLAIN LATHE

This 1956 model Bl 92430 FAB 149 has a plain bearing W20 headstock and was used exclusively for the restoration of clocks and instruments, we are selling this on behalf of one of our customers and considering its age is in very good condition, would benifit with a repaint! [Read more…]

SMALL VERTICAL SLIDE

SMALL VERTICAL SLIDE

SMALL VERTICAL SLIDE

This vertical slide has no manufactures identification mark on it, has some oil or grease staining in the front face but otherwise is unmarked. The height of the slide overall is 4″ and moves verticaly to 5″ there are no graduations on the hand wheel. The slot width on face is 9/32″ [Read more…]

POTTS MILLING AND DRILLING SPINDLE

POTTS MILLING AND DRILLING SPINDLE

POTTS MILLING AND DRILLING SPINDLE

An unpainted example of this home constructed spindle. It can be attached to most vertical slides, lathe crosslides and some wheel cutting engines. The spindle takes 8mm collets and has a two speed pulley. This has seen very lttle use and has no play on the bearings. Made in Britain Built to Last™ weighs in [Read more…]

J.M.WILD WHEEL CUTTING & MILLING SPINDLE

J.M.WILD WHEEL CUTTING & MILLING SPINDLE

J.M.WILD WHEEL CUTTING & MILLING SPINDLE

This sets the standard for wheel cutting and milling spindles. Built to a very high standard with pre – loaded bearings and heavy duty construction they give years of service. It will fit straight on to the Myford vertical slide with the aid of extended T bolts, but will [Read more…]

MILLING SPINDLE

MILLING SPINDLE

This Spindle is likely to be an early model by Arund Engineering the latter models were of sqaure construction with the mounting holes drilled through the block and will fit straight on to a Myford vertical slide. They were very well made in solid cast iron with high quality bearings. The spindle will [Read more…]