Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive a reply.

I HAVE BEEN ADVISED BY CARL BARNES THAT THE BRUNEL CLOCK AND WATCH FAIR ON SUNDAY THE 5th APRIL HAS BEEN CANCELLED DUE TO THE CURRENT VIRUS SITUATION.

 

Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

LORCH LLK HIGH PRECISION INSTRUMENT LATHE

LORCH LLK HIGH PRECISION INSTRUMENT LATHE

A used model of this well sought after lathe built in 1965 No 29148. However it is in need of a strip down overhaul and re-paint in fact an ideal project. This would make an ideal lathe in any clock or model makers workshop. It comes with the following [Read more…]

PULTRA 1750 10MM BENCH LATHE

PULTRA 1750 10MM BENCH LATHE

A well equipped clean bench model which just needs mounting on a bench with the Mardrive unit to be used straight away. The Mardrive is single phase 240 volt with switch gear and clutch and brake pedal. Comes with the following equipment:-

Set of 24 metric collets from .4 – [Read more…]

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

UNIMAT THREE WITH MILLING/DRILLING ATTACHMENT

A clean used example of this well know lathe that is always popular with Model Makers, Horologists etc. Has some oil staining on the bed but is otherwise in very good condition. Comes with the following inventory of equipment:-

3 jaw reversable chuck [Read more…]

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW CHUCK

EMCO 55mm 3 JAW (reversible) CHUCK

This will fit the early Unimat and other variants in the Emco range. In used but very good condition and could be fitted to other small lathes.Will post Royal Mail Special Delivery UK only including packing for£9.50.

NOW SOLD

[Read more…]

BOLEY & LEINEN 8mm RING STEP CHUCKS

BOLEY & LEINEN RING STEP CHUCKS

BOLEY & LEINEN RING STEP CHUCKS

These 5 Boley and Leinen ring step chucks are marked 1,3, and 5, 2and 4 are not. All are marked Boley and Leinen and cover the sizes in the set. They are all in excellent condition. Please call for any further information, The block is not supplied. Will post [Read more…]

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

TRIPLE CROSSLIDE

A rare American HR triple crosslide that would suit WW pattern lathe beds. This is very similar to the Derbyshire and Webster Whitcomb makes. The chrome plating has aged a little and there is very slight flaking on one edge, there is a slight cut mark on the topslide (shown) but would not [Read more…]

4 JAW CHUCK

4 JAW CHUCK

A very clean 59mm diameter 4 jaw independent chuck with a 12 x 1mm internal thread and register, would suit a late Cowells lathe. Comes with a key. Will Post UK only Royal Mail Special delivery for £10.00 including packing.

 

NOW SOLD

[Read more…]

WW PATTERN 8mm LATHE

WW PATTEN 8mm LATHE

WW PATTERN 8mm LATHE

A single foot ww pattern 8mm lathe, no makers mark but could be from Webster Whitcomb or another American company. Has been used but is in good condition with no cuts or marks on the bed and headstock bearings running smoothly. There a few chips on the composite headstock pulley but [Read more…]

PULTRA 10mm STEP CHUCKS

PULTRA 10mm STEP CHUCKS

A set of 5 10mm Pultra step chucks marked “Conflex ” so late models. These are in outstanding condition and probably not used, very light staining in some of the steps but otherwise as new. Will post UK only Royal Mail Special Delivery including packing for £8.60 or buyer collects or [Read more…]

SET OF 6mm STEP CHUCKS

SET OF 6mm STEP CHUCKS

SET OF 6mm STEP CHUCKS

A very clean set of step chucks, slight oil or preservative staining on the ring section but otherwise in mint condition. There is no makers mark but they are very much in the style of the Lorch step collet. The thread is 5 x .7mm for the draw bar. Will [Read more…]