Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive a reply.

I HAVE BEEN ADVISED BY CARL BARNES THAT THE BRUNEL CLOCK AND WATCH FAIR ON SUNDAY THE 5th APRIL HAS BEEN CANCELLED DUE TO THE CURRENT VIRUS SITUATION.

 

Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

ACIERA F1 UNIVERSAL PRECISION MILLING MACHINE

ACIERA F1 UNIVERSAL PRECISION MILLING MACHINE

Here we have an early imperial example of this much sought after miller favored by horologists and fine model makers the world over. This one will require striping down for cleaning and a re-paint to get it back to the condition when new. The motor is three phase and [Read more…]

ACIERA F12 UNIVERSAL PRECISION MILLING MACHINE.

ACIERA F12 UNIVERSAL PRECISION MILLING MACHINE.

Here we have an incomplete example of this forerunner of the iconic F1. Despite it`s unkempt appearance underneath the grime and staining is a very useful basis for an accurate horizontal miller. There is little wear in the slides and the handles and the leadscrews are not bent. The [Read more…]

EMCO SMALL MACHINE VICE

EMCO SMALL MACHINE VICE

This small machine vice has overall dimensions of 85mm long X 45mm wide X 34mm height. The jaws open to 31mm by 17mm deep, the static jaw has horizontal and vertical V cuts so round objects can be held easily. The vice has some oil and grease staining but is otherwise [Read more…]

B C A JIG BORER

B C A JIG BORER

A very clean example of this popular machine used exstensivly for fine modelling and horology, This one belongs to a customer who whishes to move it on. This one comes with all the tooling and eqiupment shown and has the advantage of an inverter drive all mounted on a clean [Read more…]

JOHN STEVENS MICRO MILL

JOHN STEVENS MICRO MILL

JOHN STEVENS MICRO MILL

A rare chance to obtain one of Johns micro mills in as new condition. Built to exceptionaly high standards this mill is one of only two constructed. It comprises of a cast iron base to which the single 6mm tee slotted milling table is attached which has a movement of 120mm [Read more…]

COWELLS 90ME LATHE

COWELLS 90ME LATHE

COWELLS 90ME LATHE

A very well equipped example of this well known and widley used British made lathe. It is the older version with a 14X 1.25 mm nose thread,however the dividing head nose thread is 14X1.00mm. This one comes with the wheel and pinion cutting attachment and was set up to be used this [Read more…]

EMCO UNIMAT 3 PRECISION LATHE and MILL

EMCO UNIMAT 3 PRECISION LATHE and MILL

EMCO UNIMAT 3 PRECISION LATHE and MILL

A very clean and well equiped model of this popular all rounder. This one takes Chronos dividing plates on the back of the headstock spindel No`s DD62 & DD63 ( as well as having the emco dividing unit and 4 plates ) so wheels and pinions can be [Read more…]

SMALL INDEXING HEAD

SMALL INDEXING HEAD

SMALL INDEXING HEAD

This small indexing unit only measures 2 1/4″ X 1 1/4″ x 2 1/42 high and would fit well on any high precsion mills such as the Aceria F1 or the Sixis or any other smaller millers. Made to a very high standard ( We have not been able to identify a [Read more…]

SIGMA JONES BENCH MILL / JIG BORER

SIGMA JONES BENCH MILL / JIG BORER

SIGMA JONES BENCH MILL / JIG BORER

A good working example of this popular machine. Powered by a single phase 1/2 HP motor ( Tuscan flame proof Type) with counter balance belt tensioning and offering a good range of speeds this is a very versatile machine. Not shown in the picture but included is a [Read more…]

PROXON MILL/DRILL COMBINATION

PROXON MILL/DRILL COMBINATION

PROXON MILL/DRILL COMBINATION

This mill drill can be broken down and the motor used as a variable high speed drill or grinder. The combination is made up of the following units:-

BFW mill drill and speed controller. BFB mill drill stand KT compound table A set of 6 collets.

The head can be positioned in [Read more…]