Oops! It appears that you have disabled your Javascript. In order for you to see this page as it is meant to appear, we ask that you please re-enable your Javascript!

Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.

Tel: 01235 763987
Fax: 01235 769828

Browse our site

Reset

ARRAND BALL BEARING SPINDLE

ARRAND BALL BEARING SPINDLE

ARRAND BALL BEARING SPINDLE

A little used example of this well known make that has been used in model engineering and horology for many years sadly no longer available to buy new. This one comes with three 1 Morse adaptors for holding the following (1) 3/16th round toolsteel (2) 1/4 round toolsteel (3) to hold […]

B C A JIG BORER

B C A JIG BORER

A very clean example of this popular machine used exstensivly for fine modelling and horology, This one belongs to a customer who whishes to move it on. This one comes with all the tooling and eqiupment shown and has the advantage of an inverter drive all mounted on a clean […]

JOHN STEVENS UNIVERSAL MICRO MILL & DRILL

JOHN STEVENS UNIVERSAL MICRO MILL & DRILL

JOHN STEVENS UNIVERSAL MICRO MILL & DRILL

This uniqe machine has been constructed from the base of a small bench single operation mill. John has as usual performed his magic to resurrect it to a very useful machine. The footprint is 420mm X 400mm and has a maximum height ( vertical slide extended ) of […]

COWELLS 90ME LATHE

COWELLS 90ME LATHE

COWELLS 90ME LATHE

A very well equipped example of this well known and widley used British made lathe. It is the older version with a 14X 1.25 mm nose thread,however the dividing head nose thread is 14X1.00mm. This one comes with the wheel and pinion cutting attachment and was set up to be used this […]

EMCO UNIMAT 3 PRECISION LATHE and MILL

EMCO UNIMAT 3 PRECISION LATHE and MILL

EMCO UNIMAT 3 PRECISION LATHE and MILL

A very clean and well equiped model of this popular all rounder. This one takes Chronos dividing plates on the back of the headstock spindel No`s DD62 & DD63 ( as well as having the emco dividing unit and 4 plates ) so wheels and pinions can be […]

SCHAUBLIN 102 PLAIN LATHE

SCHAUBLIN 102- 80 PLAIN LATHE

This 1956 model Bl 92430 FAB 149 has a plain bearing W20 headstock and was used exclusively for the restoration of clocks and instruments, we are selling this on behalf of one of our customers and considering its age is in very good condition, would benifit with a repaint! […]

SMALL VERTICAL SLIDE

SMALL VERTICAL SLIDE

SMALL VERTICAL SLIDE

This vertical slide has no manufactures identification mark on it, has some oil or grease staining in the front face but otherwise is unmarked. The height of the slide overall is 4″ and moves verticaly to 5″ there are no graduations on the hand wheel. The slot width on face is 9/32″ […]

POTTS MILLING AND DRILLING SPINDLE

POTTS MILLING AND DRILLING SPINDLE

POTTS MILLING AND DRILLING SPINDLE

An unpainted example of this home constructed spindle. It can be attached to most vertical slides, lathe crosslides and some wheel cutting engines. The spindle takes 8mm collets and has a two speed pulley. This has seen very lttle use and has no play on the bearings. Made in Britain Built to Lastâ„¢ weighs in […]

J.M.WILD WHEEL CUTTING & MILLING SPINDLE

J.M.WILD WHEEL CUTTING & MILLING SPINDLE

J.M.WILD WHEEL CUTTING & MILLING SPINDLE

This sets the standard for wheel cutting and milling spindles. Built to a very high standard with pre – loaded bearings and heavy duty construction they give years of service. It will fit straight on to the Myford vertical slide with the aid of extended T bolts, but will […]

MILLING SPINDLE

MILLING SPINDLE

This Spindle is likely to be an early model by Arund Engineering the latter models were of sqaure construction with the mounting holes drilled through the block and will fit straight on to a Myford vertical slide. They were very well made in solid cast iron with high quality bearings. The spindle will […]