Oops! It appears that you have disabled your Javascript. In order for you to see this page as it is meant to appear, we ask that you please re-enable your Javascript!

Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive it.

Tel: 01235 763987
Fax: 01235 769828

 

Browse our site

Reset

GERMAN PIVOTER JACOT TOOL

GERMAN PIVOTER JACOT TOOL

This offset Jacot tool has had good careful use. All the pivot plates (including 2 spares ) and drums show no signs of damage or wear. The box bears all the marks of being taken out a draw and replaced many times. No makers marks on the tool but finished to […]

8mm MANDREL PLATE & CENTRE

8mm MANDREL PLATE & CENTRE

Although not marked this is very much in the Pultra style. we have resurfaced the plate, One of the dogs has a slight rub mark on the top edge but all the gripping surfaces are unmarked. The pull back centre point is sharp and the guide bush allows the pin […]

WATCHMAKERS DEPTHING TOOL

WATCHMAKERS DEPTHING TOOL

Good quality depthing tool in clean wooden case, points and centres in excellent condition, pins in line. Will post UK only Royal mail special delivery including packing for £10.00.

PRICE £35.00

4 JAW CHUCK

4 JAW CHUCK

A very clean 59mm diameter 4 jaw independent chuck with a 12 x 1mm internal thread and register, would suit a late Cowells lathe. Comes with a key. Will Post UK only Royal Mail Special delivery for £10.00 including packing.

PRICE £40.00

[…]

2 BOXES OF SPARE STAKES

2 BOXES OF SPARE STAKES

2 BOXES OF SPARE STAKES

The two wooden containers hold 19 and 20 spare 4.7mm stakes that will fit most sets on the market today. They are marked Southern clock and watch supplies and the other “Precista”. All stakes are in good clean condition, one has been ground to fit the previous owners requirements it […]

LORCH SCHMIDT MANDREL HEADSTOCK

LORCH SCHMIDT MANDREL HEADSTOCK

LORCH SCHMIDT MANDREL HEADSTOCK

This “D” Bed headstock is in good used condition, there is no play in the bearings and the centring point is sharp. The nickel plating has come of the headstock in a few places so looks a little dull. The three plate clamps are all flat and have no damage. The […]

SET OF 8mm STEP CHUCKS

SET OF 8mm STEP CHUCKS

SET OF 8mm STEP CHUCKS

A made up set of 8mm ring chucks in good used condition with some staining in the ring sections. They are probably of Pultra origin judging by the marks on them. Will post UK only Royal Mail Special Delivery only for £10.00 including Packing.

PRICE £85.00

[…]

I M E 8mm MANDREL FACE PLATE

I M E 8mm MANDREL FACE PLATE

I M E 8mm MANDREL FACE PLATE

A rare example of an IME mandrel face plate in good used condition, regrettably came in with no center pin but easily made from silver steel, Diameter would need to be 3.97mm or .1560ins. The jaws on the clamps are not nicked or damaged and the plate has […]

SET OF 6mm STEP CHUCKS

SET OF 6mm STEP CHUCKS

SET OF 6mm STEP CHUCKS

A very clean set of step chucks, slight oil or preservative staining on the ring section but otherwise in mint condition. There is no makers mark but they are very much in the style of the Lorch step collet. The thread is 5 x .7mm for the draw bar. Will […]

COLIN WALTON WHEEL & PINION CUTTING ATTACHMENT

COLIN WALTON WHEEL & PINION CUTTING ATTACHMENT

COLIN WALTON WHEEL & PINION CUTTING ATTACHMENT

A very compact unit that will easily fit most lathes including the Pultra 1770 and WW pattern at the smaller end of the scale. This one did not come with an original division plate but as shown will take the earlier pattern Chronos plates with the smaller central […]