Contact Us

You can use the contact form on our “About” page, or use the form below regarding any tool that interests you.
Please make sure you complete all the information asked for otherwise we will not receive a reply.

 

Tel: 01235 763987
Fax: 01235 769828

Browse our site

Reset

MEDDINGS PACERA BENCH DRILL PRESS

MEDDINGS PACERA BENCH DRILL PRESS

MEDDINGS PACERA BENCH DRILL PRESS

This 1/2″ capacity model has been used but well looked after with just a couple of nicks on the adjustable table. The drive is by a single phase 240 volt 1/3 HP motor to a 5 speed pulley set giving the following speeds 500, 900, 1400, 2300, and 4000 rpm [Read more…]

PROXON BSG 220 DRILL SHARPENER

PROXON BSG 220 DRILL SHARPENER

PROXON BSG 220 DRILL SHARPENER

In as new condition, we believe it`s never been run.This drill sharpener will accurately produce standard 118 degree drill points and the correct relief angle. It can take drills from 3 mm – 13 mm and includes a dressing stone for truing the wheel. Good value and well made.

NOW [Read more…]

PROXON MILL DRILL SYSTEM

PROXON MILL DRILL SYSTEM

PROXON MILL DRILL SYSTEM

This system is derived from 3 separate units that are combined to form a very compact and versatile machine that would suit a model makers or horologist`s workshop. The 200 x 200 mm sqaure X Y table has 150 x 150 mm movement and is bolted directly to the stand base.The [Read more…]

JONES & SHIPMAN PRECISION BENCH DRILL

JONES & SHIPMAN PRECISION BENCH DRILL

JONES & SHIPMAN PRECISION BENCH DRILL

This reconditioned example of this well known maker is in very good condition. It is fitted with a new GEC 250 volt single phase motor with an output of 250 Watts. The Quill travel is 1 1/2″ and has an adjustable depth stop and is fitted 15/64 capacity [Read more…]

PINNACLE BENCH DRILL

PINNACLE BENCH DRILL

PINNACLE BENCH DRILL

This model come withe 12 speeds from 110 rpm – 3110 rpm and is powered by a G E C 1/2 HP 220 – 240 volt single phase motor. Drills are held in a 2 Morse quill, or by a 3 jaw Jacobs style chuck ,the quill 3 1/2″ of travel . [Read more…]

RECORD POWER BENCH DRILL

RECORD POWER BENCH DRILL

RECORD POWER BENCH DRILL

A very clean example of this 1/2 capacity bench drill, cast iron construction throughout makes for a very solid machine. This one has 5 speed from 540 rpm – 2430 rpm and is powered by a Brook Crompton 180 watt 23o-250 volt mains motor. There is 9 1/2″ under the chuck [Read more…]

CLASSIC CLOCK MAKERS DRILL

CLASSIC CLOCK MAKERS DRILL

CLASSIC CLOCK MAKERS DRILL

A great favorite with clock makers and model engineers, usually made by the user from a kit of castings. There were several variations to the design some of which could be used for staking and punch work. This one comes with 1/4″ Jacobs chuck and is powered by a Crompton Parkinson [Read more…]

OVERBECK HIGH PRECISION DRILL

OVERBECK HIGH PRECISION DRILL

OVERBECK HIGH PRECISION DRILL

This German built high precision drill is designed for small hole drilling and operates with automatic down feed that is controlled by the lever on the left hand side of the machine. The drill is powered by .2 kw mains motor, a speed controller could be fitted such as an inverter [Read more…]

MICRO MILL/DRILL

MICRO MILL/DRILL

This Chester micro mill/drill is compact and will be able to perform a wide variety of tasks, and will be very much at home in the model engineers or Horologist workshop. It has a high and low range of variable speeds 0-3600 and 0-5000 rpm this achieved by a simple belt change and [Read more…]

DRAPER D 16/16 BENCH DRILL PRESS

DRAPER D 16/16 BENCH DRILL PRESS

This model has the 12″ round table with rack rise and fall and tilt facility, with 16 speeds ( 210-3340 ) and its 350 watt 1/2 HP motor it can take on most jobs in any model engineers workshop. This also has a No 2 Morse sleeve quill which [Read more…]